![pageSearch](/themes/hestia/images/page-search.webp)
Bio
Aug 29, 2023Seattle clean tech startup lands $1.4M for eco
Aug 19, 2023Plastic Labware Market to Reach $19.83 Billion by 2028, Bellco Glass, Corning, DWK Life Sciences, Sartorius, and Thermo Fisher Scientific are the Major Stakeholders
Aug 11, 2023Desiccators Market Size Expected to Fly High with Increased Demand
Aug 25, 2023High Pressure Reactors, Customized Reactors, Test Autoclaves
Aug 28, 2023Bipolar membrane electrolyzers enable high single
![Jan 25, 2024](/themes/hestia/images/news-details-icon1.webp)
Nature Communications volume 13, Article number: 3609 (2022) Cite this article
12k Accesses
38 Citations
11 Altmetric
Metrics details
In alkaline and neutral MEA CO2 electrolyzers, CO2 rapidly converts to (bi)carbonate, imposing a significant energy penalty arising from separating CO2 from the anode gas outlets. Here we report a CO2 electrolyzer uses a bipolar membrane (BPM) to convert (bi)carbonate back to CO2, preventing crossover; and that surpasses the single-pass utilization (SPU) limit (25% for multi-carbon products, C2+) suffered by previous neutral-media electrolyzers. We employ a stationary unbuffered catholyte layer between BPM and cathode to promote C2+ products while ensuring that (bi)carbonate is converted back, in situ, to CO2 near the cathode. We develop a model that enables the design of the catholyte layer, finding that limiting the diffusion path length of reverted CO2 to ~10 μm balances the CO2 diffusion flux with the regeneration rate. We report a single-pass CO2 utilization of 78%, which lowers the energy associated with downstream separation of CO2 by 10× compared with past systems.
CO2RR for C2+ production requires the simultaneous achievement of high production rate and high energy efficiency1,2. The current densities in flow cells (A in Table 1) and membrane-electrode assemblies (MEAs, B in Table 1) have reached industrially relevant levels (ethylene partial current density > 100 mA cm−2)3; however, the energy penalty associated with low single-pass CO2 utilization (SPU: the fraction of the CO2 converted to the total input CO2) has yet to be reduced to practical levels (SPU > 40%)4. Carbonate formation and crossover in typical CO2RR electrolyzers limit the SPU to ≤25% for C2+ (details in SI1), imposing energy penalties of 280–480 GJ in alkaline-media, and of 80–130 GJ in neutral-media, for the production of each ton of ethylene5,6.
Analysis of the CO2 and carbonate mass balance in neutral-media electrolyzers (SI1) indicates that achieving high SPU requires that (bi)carbonate not cross the membrane to the anode, and that (bi)carbonate formed at the cathode must revert to CO2 and remain available to participate in CO2RR by returning to the cathode.
Bipolar membranes (BPMs) have been used to block CO2 crossover and convert (bi)carbonate back to CO27,8,9. In CO2RR electrolyzers, commercial BPMs inhibit CO2 loss10, but the acidic cation-exchange layer (CEL) degrades the cathode’s CO2RR selectivity10.
To address cathode acidification, one may use a buffering catholyte (e.g., KHCO3) between CEL and cathode9,11,12; this approach (Fig. 1a) provides a pH at the CEL surface of ~3, and keeps the cathodic local pH >12. However, in a buffering catholyte, (bi)carbonate reverts to CO2 near the surface of the CEL (solid black line in Fig. 1a), slowing mass transfer of the reverted CO2 and reducing reactant availability for CO2RR. This leads to the best SPUs reported of ~15% in prior BPM-based electrolyzers in C2+ electroproduction (SI3 and SI5). When the catholyte is flowing, the SPU is even lower, ~6% according to previous reports, because flowing catholyte removes reverted CO211. Prior BPM-based electrolyzers (Table 1) have, as a result, not exceeded the 25% SPU limitation for C2+ electroproduction (SI3).
a The CO2 (solid lines) and pH distributions (dashed lines) in the 65 μm-thick SC-layer. The positions where the (bi)carbonates revert to CO2 are marked (red for non-buffering and black for buffering electrolyte). b The schemes and the mass transfer in the SC-BPMEA. c The pH distribution inside the SC-layer. d The dissolved CO2 concentration profile inside the SC-layer. The virtual boundaries marked by dash lines are defined as the position where the CO2 concentration becomes 1% lower than the bulk concentration. The numbers marked above are the distances between the virtual boundaries and the cathode surface.
We show that a stationary, non-buffering catholyte with well-designed catholyte layer thickness (Fig. 1b) addresses these mass-transfer limitations while simultaneously providing the needed high local cathode pH (Fig. 1a). BPM-generated protons migrate farther in non-buffering catholyte than in buffering catholyte, since the latter consumes protons at a higher rate. Here we show further quantitative analysis of the design requirements to achieve this target.
The composition and thickness of the catholyte layer influence the local pH, the efficiency of CO2 regeneration and, thereby, the overall cell performance. We applied a one-dimensional multiphysics model in COMSOL to investigate the catholyte layer in BPM-based CO2RR electrolyzers.
The CO2 reactant is provided by two sources: the inlet CO2 flow (gas) and the regenerated CO2 (dissolved form, aq.) in the catholyte. To achieve high SPU, it is necessary to restrict the gaseous CO2 feed13,14. Under a restricted gaseous CO2 availability, the cathode CO2 supply relies more on regeneration (SI1): in an ideal case with 100% SPU and 100% C2+ selectivity, regeneration contributes 75% of the consumed CO2. Thus, the mass transport of regenerated CO2 is most critical, and that transport is governed by catholyte composition and thickness.
At steady-state, electrolysis creates a pH gradient through the catholyte layer: the pH is high near the cathode and low near the CEL. The protons and (bi)carbonate ions recombine in the catholyte, forming CO2 (aq.) that diffuses, in response to a concentration gradient, to the Cu catalyst.
Simulations resolve the local cathode environment as a function of dimensions, electrolyte, and running conditions (Figs. 1a, c, d, SI4 and SI5). We selected 250, 125, 65, and 16 μm as the modelled thicknesses to correspond to commercially available materials.
Use of a buffering catholyte (e.g., KHCO3) leads to a thick CO2 (aq.) diffusion layer close to the catholyte thickness, since the CO2 (aq.) is generated near the CEL surface, as shown in Fig. 1a (details in SI5). This effect reduces the CO2 (aq.) mass-transfer efficiency. The experimental results presented and discussed in SI6 show similar trends to the simulation results.
In contrast, Fig. 1a, c illustrate that with a non-buffering catholyte layer (e.g., 0.5 M K2SO4) with thicknesses of 250, 125, and 65 μm, the local pH values near the cathode are greater than 11, which is sufficient to promote selectivity towards CO2RR over HER13. Reducing the SC-layer thickness to 16 μm results in a cathode pH of 8.7, implying a lower selectivity toward CO2RR.
Figure 1c, d shows the simulated concentration profiles of CO2 (aq.) in the non-buffering SC-layer. At steady-state, the CO2 (aq.) is continuously supplied to the cathode to participate in CO2RR, forming a concentration gradient (the boundary was defined here as the position where CO2 concentration is 1% lower than the saturated concentration) to the cathode surface. Prior studies have termed the zone between the cathode and this boundary the diffusion layer15. The thickness of the diffusion layer controls the efficiency of CO2 (aq.) mass transport15. According to the simulations, the thicknesses of the diffusion layers are 75, 35, 12, and 5 μm for the catholyte layers with the thicknesses of 250, 125, 65, and 16 μm, respectively (marked in Fig. 1d). For reference, the CO2 (aq.) diffusion layer thickness in H-cells (all CO2 supplied in dissolved form) is typically 40–100 μm, and this does not support current densities exceeding 100 mA cm−2.16 We expect that diffusion layers <40 μm, and a corresponding catholyte thickness <150 μm, are required for sufficient mass transport in a non-buffering catholyte. To achieve similar mass transport in a buffering catholyte, the total thickness could not exceed 12 μm, and the cathodic pH would not be sufficiently alkaline for selective CO2RR (SI5).
The simulation results suggest the following design principles for the catholyte layer in a BPM-based electrolyzer: the local cathode pH and the diffusion layer thickness of the regenerated CO2 increase as the catholyte thickness increases; the buffering capacity of the catholyte increases the diffusion layer thickness and reduces transport. Precise control of the thickness of a non-buffering catholyte should thus offer a route to high SPU, CO2RR selectivity, and reaction rate.
Guided by the above analysis, we focused on a stationary catholyte bipolar membrane electrode assembly (SC-BPMEA) electrolyzer and incorporated a judiciously-designed catholyte layer and BPM (Fig. 1a).
The cathode was prepared by spraying Cu nanoparticles onto a hydrophobic carbon gas-diffusion layer for CO2RR (Fig. 2a). The anode was IrO2 supported on Ti felt for the oxygen evolution reaction (OER). A BPM (SEM in Fig. 2b) under reverse bias was employed with the anion exchange layer (AEL) contacting the anode and the CEL contacting the SC-layer (porous support saturated with electrolyte). The cathode was compressed onto the porous layer, and the anode and cathode flow-field plates sandwiched the system.
Scanning electron microscopy (SEM) images of the cathode electrode (a) and the CEL/AEL interface of the custom BPM used for SC-BPMEA in neutral 0.1 M KHCO3 anolyte (b). The custom BPM consists of a NafionTM 212 as CEL, Piperion (Versogen) as AEL, and a TiO2 nanoparticle layer sandwiched in between as the water dissociation catalyst. c The CO2/O2 ratio in the anode gas stream for the conventional electrolyzers (red squares) and our SC-BPMEA (black squares) at various current densities. O2 and CO2 flow rates in the SC-BPMEA are also indicated. The plots show data obtained after 1 h of continuous electrolysis at each current density. The data are from an SC-BPMEA with a 125 μm-thick SC-layer. Similar data were collected for 65 and 250 μm layers (difference below 5%). The error bars represent the standard deviation of three measurements.
The BPM employed in this work sandwiched TiO2 nanoparticles as the water dissociation catalyst17. This custom BPM can lower the cell voltage by ~1 V compared with commercial BPMs (e.g., Fumasep, details in SI2). The full cell voltage of such custom BPM-based electrolyzers is close to that of anion exchange membrane (AEM)-based systems.
Measurements of the CO2/O2 ratio in the anode gas stream show that the SC-BPMEA effectively prevents CO2 crossover, as required for high SPU (SI1)8,11. In agreement with the previous studies8,11, the AEM-based MEA (AEMEA) showed an anode CO2/O2 ratio of ~2 for current densities ranging from 100 to 300 mA cm−2 (Fig. 2c). In conventional AEMEAs, the anionic charge carriers are CO32−, and thus suffer the loss of one molecule of CO2 for every two electrons transferred. The anode CO2/O2 ratio in the SC-BPMEA (0.06 at 200 mA cm−2) is one order of magnitude lower. Control experiments confirm that the CO2 detected in the anode is not due to acidification of anolyte (using 0.1 M K2SO4 instead of 0.1 M KHCO3 resulted in a similar CO2 /O2 ratio, Supplementary Fig. 3). The anode CO2/O2 ratio decreases as the operating current density increases, an effect we ascribe to an increased flux of protons toward the cathode. This flux decreases the pH at the CEL surface and reduces the diffusion of CO2 and HCO3−/CO3− in the CEL18,19.
As predicted from simulations, the thickness of the stationary catholyte has a major impact on cell voltage. The cell voltage of the SC-BPMEA decreases as the thickness of the SC-layer decreases (Fig. 3a) from 250 μm (5.1 V, 200 mA cm−2) to a minimum at 65 μm (3.8 V, 200 mA cm−2). Further thinning the catholyte to 16 μm resulted in higher voltage (4.4 V, 200 mA cm−2)—an effect of the lower-porosity support layer used in the 16 μm case (<20% vs. >70% for the thicker layers, see Supplementary Fig. 13a and SI7). A longer ion migration path and higher ohmic resistance partially explain the 0.67 V cell voltage increase as the stationary catholyte thickness increases from 65 to 125 μm. Based on the independently measured ohmic resistance (Supplementary Fig. 13a), increasing the SC-layer thickness from 65 to 125 μm imposes an ohmic voltage increase of merely 0.07 V at 200 mA cm−2. Similarly, compared to 65 μm, the 250 μm SC-layer increases the ohmic voltage loss by 0.24 V at 200 mA cm−2, while the cell voltage increases by 1.3 V.
All the results are collected at 35 °C with a CO2 flow rate of 10 sccm cm−2 (normalized by the geometric area of the cathode), a catholyte of 0.5 M K2SO4, and an anolyte of 0.1 M KHCO3. a The dependence of cell voltages on current density. b Distribution of voltage losses measured in the SC-BPMEA with 65 μm thick catholyte operating at 200 mA cm−2 (cell voltage = 3.82 V). The breakdown of the voltage is explained in SI7 of the Supplementary Information. The dependence of the CO2RR gas products FE on the current density for the SC-BPMEAs with the catholyte thickness of 250 (c), 125 (d), and 65 μm (e). The FE result for 16 μm is shown in Supplementary Fig. 12. The error bars represent the standard deviation of three measurements.
The simulations (Fig. 1d) indicate that the thicker SC-layer results in longer transport distances for dissolved CO2. The CO2 regeneration rate inside the SC-layer also depends on the current density, and for thicker SC-layers (e.g., >125 μm), CO2 bubbles are more prone to form near the CEL. These bubbles obstruct ion migration, increasing the ohmic resistance of the SC-BPMEA. Electrochemical impedance spectroscopy measurements (Supplementary Fig. 13d, e) also support this finding. An applied current of 200 mA cm−2 resulted in an insignificant change to the high-frequency resistance (HFR) of the SC-BPMEA with a 65 μm-thick SC-layer; while, in contrast, the HFR of the SC-BPMEA with a 125 μm-thick SC-layer increased by 120% after applying 200 mA cm−2 for 20 min, leading to a cell voltage 0.6 V higher than for the 65 μm SC-layer.
The cell voltage of the SC-BPMEA with a 65 μm SC-layer operating at 200 mA cm−2 is 3.8 V, comparable to the AEM-based neutral-media MEAs operating at similar conditions (difference <±0.05 V)20,21,22. This result demonstrates that the cell voltage of a BPM-based CO2RR electrolyzer can be as low as that of an AEM-based electrolyzer with a current density of up to 200 mA cm−2, while suppressing unwanted crossover and providing high SPU.
Figure 3b shows the breakdown of the 3.8 V cell voltage, determined using methods reported previously13,21 (SI7). The factors making up the cell voltage include the thermodynamic potential, cathode overpotential, anode overpotential, ohmic loss, and Nernstian/concentration overpotential (i.e., due to pH gradient)21. The sum of these factors accounts for most of the cell voltage, suggesting that the water dissociation overpotential at the AEL/CEL interface of the BPM is small in the SC-BPMEA at 200 mA cm−2, in agreement with previous reports employing BPMs fabricated in this way (SI2 and ref. 17).
The thickness of the SC-layer also affects selectivity towards CO2RR. With thicknesses of 65, 125, and 250 μm, the H2 Faradaic efficiencies (FEs) are consistent (~20% at 200 mA cm−2, Fig. 3c–e), confirming that high local pH conditions are maintained the cathode in these cases (Fig. 1c). However, reducing the thickness to 16 μm increases the H2 FE to 88% at 200 mA cm−2 (Supplementary Fig. 14), consistent with a cathodic pH that is reduced due to fast proton transport through a thin SC-layer. Without restricting CO2 availability (the performance in Fig. 3 was recorded at a CO2 flow rate of 10 sccm cm−2), the SC-BPMEAs with the SC-layer thickness of 65, 125, and 250 μm show similar ethylene FE of 35–43%.
By suppressing the crossover of CO2 (e.g., <0.5% of total CO2 input at 200 mA cm−2, Figs. 2c and 4e), the SC-BPMEA surpasses the SPU of conventional CO2-to-C2+ electrolyzers, in which carbonate is the dominant charge carrier. Measuring the CO2 SPUs with a restricted CO2 flow rate is a direct approach to determining the upper bound of SPU in the CO2RR electrolyzers13.
All the measurements were conducted at 35 °C and 200 mA cm−2, and the data were collected after 2 h of continuous operation. a–c The FE distributions and the CO2 requirements (total CO2 converted to products) of the SC-BPMEAs with different catholyte thickness and input CO2 flow rates (sccm normalized by electrode area). C1 refers to CO, formate, and methane. C2+ refers to ethylene, ethanol, acetate, and n-propanol. d The total CO2 single-pass utilization (the CO2-to-ethylene single-pass conversion see Supplementary Fig. 13a) for the SC-BPMEAs with different catholyte thickness and input CO2 flow rates. e Carbon balance in SC-BPMEA with 65 μm 0.5 M K2SO4 at different input CO2 flow rates. See Supplementary Fig. 13b for plots on a logarithmic scale. f The comparison of the energy cost distributions among state-of-art CO2-to-ethylene electrolyzers. The SC-BPMEA case refers to the input CO2 flow rate of 1.17 sccm cm−2. The error bars represent the standard deviation of three measurements.
As the inlet CO2 flow rate decreased, the C2+ FE of the SC-BPMEA at 200 mA cm−2 decreased, accompanied by an increase in the H2 FE (Fig. 4a–c). With SC-layer thicknesses of 65 μm (Fig. 4c), as the input CO2 flow rate decreases from 1.17 to 0.58 and 0.29 sccm cm−2, the C2+ FE decreases from 49 to 48% and 34%, while the H2 FE increases from 23 to 31% and 64%. This shift is consistent with a CO2 mass transport limitation13,20,21.
The stationary catholyte thickness affects the SPU of the SC-BPMEA. The SPU gradually increases up to 21, 61, and 78% for the SC-BPMEAs with SC-layer thicknesses of 250, 125, and 65 μm, respectively (Fig. 4d). These results demonstrate that high CO2 conversion efficiencies are possible using SC-BPMEAs with SC-layer thicknesses of 125 and 65 μm.
For a given CO2 flow rate, a thicker SC-layer produces a lower SPU (Fig. 4d). In the SC-BPMEA, reactant CO2 is available from the inlet gas stream and regeneration in the SC-layer. With unrestricted CO2 supply (Fig. 3c–e), the H2 FEs are similar for different stationary cathode layer thicknesses, indicating that both the CO2 availability and local pH are unaffected by catholyte thickness under excess supply conditions. The simulations suggest that the thicker SC-layer results in a lower dissolved CO2 flux to the cathode due to the smaller concentration gradient (Fig. 1d). Compared to the SC-BPMEAs with thinner SC-layers, CO2 availability with thicker SC-layers decreases more significantly with reducing CO2 flow rate, leading to a more dramatic increase in H2 FE (Fig. 4a–c).
The experimental trends are generally consistent with those of the simulations. The SC-BPMEA with a dissolved CO2 diffusion layer thicker than 75 μm (representing a 250 μm SC-layer) fails to surpass the SPU limit because of insufficient mass transfer. In contrast, a 65 μm SC-layer facilitates efficient mass transport of the regenerated CO2 (diffusion layer thickness of 12 μm) and simultaneously promotes high local cathode pH.
As demonstrated in SI10, SC-BPMEAs using acidic and alkaline electrolytes achieve carbon efficiencies comparable to those using neutral electrolytes. The compatibility of SC-BPMEAs with a range of electrolytes offers flexibility in the selection of cathode and anode catalysts. In contrast, acidic CO2-to-C2+ electrolyzers have only been demonstrated with precious metal anodes13,14.
As shown in Supplementary Fig. 18, the SC-BPMEA shows > 50-h stability operating at 200 mA cm−2 with limited CO2 availability (CO2 input flow rate of 1.42 sccm cm−2). This operating stability is competitive with that of the neutral-electrolyte-based CO2-to-C2+ electrolyzers23,24.
We attempted to extend the SC-layer strategy in a CEM-based MEA cell (i.e., SC-CEMEA, Fig. 5a) using an acidic anolyte with pH < 2.4, expecting a lower cell voltage than the SC-BPMEA while maintaining high SPU. We found that in the SC-CEMEA, the CO2 crossover was essentially eliminated. This observation is ascribed to the lower pH near the stationary catholyte layer/CEM interface, as shown in Fig. 5a.
The stationary catholyte is 0.5 M K2SO4 and the anolyte is 0.5 M K2SO4 plus 0.1 (pH = 2.37) or 0.5 M (pH = 1.84) H3PO4. All the measurements were performed at 20 °C and a CO2 flow rate of 10 sccm cm−2. a The scheme of the SC-CEMEA. b Full cell voltages at various current densities. c The gas product FEs at various current densities.
SC-CEMEA shows a lower full cell voltage (Fig. 5b) compared to the SC-BPMEA presented, partly due to the lower resistance of the CEM and the absence of water dissociation overpotential. Meanwhile, it has a reasonable CO2RR selectivity over HER (Fig. 5c) due to the cation effect and high local pH induced by the presence K+ in the SC-layer (Fig. 5a). However, this design is not amenable to steady-state operation without continuous addition of acid and salt to the anolyte, as the initial pH gradient will be eliminated due to co-ion transport and neutralization. We found the CO2RR selectivity decreases over time and approaches 100% H2 after ~3 h.
We also observed that the SC-CEMEA design periodically ejects electrolyte from the cathode flow channel, likely due to poor water balance. On the anode, the OER generates one proton per one electron transfer. The charge carriers across the CEM are primarily H+, although neutral ion pairs will diffuse as well. At the cathode K+ makes up the electrochemical double layer at the Cu surface, and the steady-state K+ profiles are governed by the electric and chemical-potential gradients that develop under operation, which usually takes tens of seconds19. H+ migrates to the cathode and combines with OH− (or CO32−/HCO3−), producing water at the cathode. The protons also drag water molecules (~1 per proton)25 by electro-osmosis. We accordingly calculate the water balance for different cathode products as listed in Table 2. The water generated and transported to the cathode appears to dilute and push out the electrolyte in the stationary catholyte layer, of which the volume is small (ca. 10 μL per cm2 electrode area). This phenomenon results in flooding of the cathode (as confirmed experimentally) and loss of supporting electrolyte, thus degrading performance. In the BPMEA design, it is likely that the BPM slows co-ion transit across the membrane, compared to the CEM, by the large outward flux of OH− and H+ from the water dissociating junction.
The energy costs (measured in gigajoules per tonne of the target product, GJ/t) for a CO2-to-C2+ electrolyzer include the electrolysis electrical energy, cathodic stream separation, and anodic stream separation13. CO2RR performance metrics of importance include cell voltage, target product FE, SPU, and CO2 crossover5. High SPU and high energy efficiency have not been accomplished simultaneously in C2+ electroproduction. In SC-BPMEAs, a higher SPU reduces the energy required for cathode separation, but the accompanying decrease in the ethylene selectivity (Fig. 4c) elevates the specific energy requirement5. We carried out a total energy assessment of the SC-BPMEA and other state-of-art CO2-to-ethylene electrolyzers and summarized the results in Table 3, Fig. 4f, and Supplementary Table 2.
The energy consumption of an alkaline CO2RR electrolyzer2 is listed in Supplementary Table 2. In such systems, CO2 and OH− react to form carbonate continuously. This carbonate has to be recovered to maintain the CO2RR performance of such a system, consuming 5.5 GJ per tonne CO25. In the alkaline CO2RR electrolyzers, ca. 63 tonne of CO2 transforms to carbonate to produce 1 tonne of ethylene, representing an energy penalty of 350 GJ5. This costs at least $1900 per tonne of ethylene, while its market price is $800–1000 per tonne26. The alkaline electrolyzers thus do not allow for ethylene electrochemical production to be yet profitable.
In neutral-media CO2RR electrolyzers, recovering the CO2 from the anodic gas stream results in significant energy costs. In the context of highly selective conversion (i.e., CO2-to-ethylene with unity selectivity), the recovery process requires an energy input of 52 GJ to produce every tonne of product. In practice, due to non-unity product selectivity, the process is even more prohibitive, i.e., requiring an energy penalty of 80–130 GJ for producing one tonne of ethylene5.
As the SPU increases from 4 to 35%, we found a dramatic decrease in energy associated with cathode separation—from 85 to 15 GJ/t ethylene (Table 3), with the ethylene FE reduced by only 2%. Further increasing the SPU beyond 35% does not substantially reduce the energy cost associated with cathodic separation (Supplementary Table 2). This finding agrees with a recent energy analysis that in a (bi)carbonate-free CO2-to-C2+ electrolyzer, improving SPU over 40% offers an insignificant benefit to the downstream separation cost4. Pursuing an SPU > 35% decreases ethylene FE by more than 4% when using the SC-BPMEA, and thus the increased input electricity cost exceeds the savings in the cathodic separation (Table 3 and Supplementary Table 2). Therefore, 35% SPU is the most favourable condition for the present SC-BPMEA.
The energy intensity of producing ethylene in SC-BPMEA is ~30% lower than that in conventional neutral-electrolyte-based CO2 electrolyzers (Fig. 4f and Table 3). In conventional neutral-electrolyte CO2-to-ethylene electrolyzers, the CO2 crossover (at least 70%)21 costs 60–90 GJ per ton of ethylene to recover CO2 from the anodic O2 stream5. Notably, this energy penalty cannot readily be reduced, independent of optimizing catalysts and operating conditions (e.g., input CO2 flow rates, reaction rates, operating temperature, and pressure)6. In contrast, crossover CO2 in SC-BPMEA is < 0.5% of the total CO2 input, minimizing the energy cost of anodic separation.
Recently, CO2-to-ethylene conversion has been achieved in acidic electrolytes in both flow cell13 and MEA configurations14. These systems enabled CO2 SPUs exceeding 75% and also mitigated the energy cost associated with anodic separation (Table 3). Owing to the strongly acidic environment, the flow cell enables an ethylene FE of 28% at a full-cell potential of 4.2 V. The acidic MEA used an anion-exchange ionomer coating on the catalyst layer to promote CO2RR over HER. The modification of the surface with the anion exchange ionomer resulted in a higher ohmic loss, and thus the cell required potentials of 3.8 and 4.4 V at 100 and 200 mA cm−2, respectively. These devices thus eliminated the anodic CO2/O2 separation energy but at the penalty of larger cell voltages and/or lower ethylene FEs. In contrast, SC-BPMEA shows a cell voltage of 3.8 V at 200 mA cm−2 with an ethylene FE of 42%—voltages and selectivities comparable to the best conventional neutral-electrolyte CO2-to-ethylene MEAs21. Compared to acidic systems, the energy intensity of the SC-BPMEA is 36% and 12% lower than acidic flow cell and acidic MEA, respectively (Fig. 4f and Table 3).
We demonstrate a BPM-based CO2-to-C2+ MEA, with a judiciously-designed SC-layer between catalyst and BPM, that overcomes the (bi)carbonate-formation reactant loss issue without compromising performance. The composition and thickness of the SC-layer determine the CO2RR performance and SPU via a strong influence on the local pH and the chemistry and transport of CO2. The buffering capacity and the thickness of the SC-layer determine the efficiency of the regeneration, the transport, and the availability of reactant CO2. These effects were predicted in simulations and supported by experiments. The SC-BPMEA design largely eliminates the energy penalty associated with the CO2 loss in electrochemical CO2 reduction.
The performance of the SC-BPMEA might be further improved using, for example, ionic liquid or other organic salts as the catholyte, and by optimizing the porosity, structure, and hydrophobicity of the porous support layers. The CO2RR performance of the SC-BPMEA might be improved with new cathodic catalysts, optimizing the loading and processing of the catalyst layer, and by implementing BPMs with further-lowered water-dissociation voltage loss. Broadly, the SC-BPMEA is a useful platform for evaluating CO2RR catalysts operating with high CO2 utilization. The strategy and findings presented here are also relevant to the electrochemical systems such as nitrate reduction and (bi)carbonate reduction, where controlling dissimilar microenvironments near each electrode is useful, and the exchange/transport of species (other than OH− or H+) between cathode and anode is problematic.
Phosphoric acid (H3PO4, 85%), potassium sulfate (K2SO4, 99%), potassium bicarbonate (KHCO3, 99.7%), potassium chloride (KCl, 99%), potassium hydroxide (KOH, 99.95%), copper nanoparticles (25 nm), NafionTM 1100 W (5 wt. % in a mixture of lower aliphatic alcohols and water) and isopropanol (IPA, 99%) were purchased from Sigma Aldrich and used as received. Titanium oxide nanoparticles (TiO2, Aeroxide P25) were purchased from Fisher Scientific and used as received. The porous supports were also purchased from Fisher Scientific: 125 μm PVDF (0.45 μm pore size), 65 μm PTFE (0.44 μm pore size) and 16 μm PC (0.4 μm pore size). NafionTM 212, NafionTM XL, Fumasep (FAS-PET-130) and titanium (Ti) felt were purchased from Fuel Cell Store. Iridium(IV) chloride hydrate (Premion®, 99.99%, metals basis, Ir 73% min) was purchased from Alfa Aesar. The water used in this study was 18 MΩ Milli-Q deionized- (DI-) water. Nafion membranes were activated through the following procedure: 1 h in 80 °C 1 M H2SO4—1 h in 80 °C H2O2—1 h in 1 M H2SO4—stored in DI-water. Fumasep was used as received and stored in 1 M KCl. Piperion (40 μm) was purchased from W7Energy and stored in 0.5 M KOH.
The water dissociation catalyst layer was fabricated following a similar procedure in a previous report17. TiO2 nanoparticles inks were prepared by sonicating the mixture of TiO2, DI-water, and IPA with the weight ratio of 1: 833: 2833 for 30 min. TiO2 nanoparticle ink was spray-coated onto a Nafion 212 membrane, of which the edges were sealed by Kapton tape. The exposed membrane dimension was 2.2 cm × 2.2 cm. The nominal loading of TiO2 is 0.2 mg cm−2. The TiO2-coated NafionTM was immediately used for assembling electrolyzers once prepared.
For the CO2RR, we prepared the gas diffusion electrodes (GDEs) by spray-depositing a catalyst ink dispersing 1 mg mL−1 of Cu nanoparticles and 0.25 mg mL−1 of NafionTM 1100 W in methanol onto a hydrophobic carbon paper. The mass loading of Cu NPs in the GDE was kept at 1.5 mg/cm2. The GDEs were dried in the air overnight prior to experiments.
The OER electrode preparation procedure involves: etching the Ti felt in hydrochloric acid at 70 °C for 40 min; rinsing the etched Ti felt with DI water; immersing the Ti felt into an Ir(IV) chloride hydrate solution; drying and sintering the Ir-loaded Ti felt. The loading, drying, and sintering steps were repeated until a final Ir loading of 1.5 mg cm−2 was achieved.
The MEA set (5 cm2) was purchased from Dioxide Materials. A cathode was cut into a 2.1 cm × 2.1 cm piece and placed onto the MEA cathode plate with a flow window with a dimension of 2.2 cm × 2.2 cm. The four edges of the cathode were sealed by Kapton tape, which also made the flow window fully covered. The exposed cathode area was measured every time before the electrochemical tests, in the range of 3.1 to 4.2 cm2. Onto the cathode, a porous support layer (2 cm × 2 cm with various thicknesses, 250 μm was stacking two 125 μm-thick PVDF) saturated with desirable electrolyte (sonicated in electrolyte for 15 min to degas) was carefully placed. This porous support layer serves as the ‘stationary catholyte layer (SC-layer).’ The considerations of membrane selection can be found in SI2 and SI4 of the Supplementary Information. When using the custom BPM, a TiO2-coated Nafion membrane was placed onto the SC-layer with the TiO2 layer facing up, then covered by a Piperion (5 cm × 5 cm) membrane. When using Fumasep BPM, the membrane was placed with its cation-exchange layer (CEL) facing the cathode side. An IrO2 loaded Ti felt (2 cm × 2 cm) was placed onto the anion-exchange layer (AEL) of the BPM.
Images of cathode and custom BPM were captured by an FEI Quanta FEG 250 environmental SEM.
Throughout all experiments, CO2 flowed to the cathode side at 10 sccm cm−2 unless otherwise specified, while the anode side was fed with neutral 0.1 M KHCO3 at 10 mL/min by a peristaltic pump unless otherwise specified. The electrochemical measurements were performed with a potentiostat (Autolab PGSTAT204 with 10A booster). The cell voltages reported in this work are not iR corrected. The system was allowed to stabilize at the specific conditions for > 1000 s before recording the results. All the error bars represent standard deviations based on three measurements.
The CO2RR gas products, oxygen, and CO2 were analyzed by injecting the gas samples into a gas chromatograph (Perkin Elmer Clarus 590) coupled with a thermal conductivity detector and a flame ionization detector. The gas chromatograph was equipped with a Molecular Sieve 5A Capillary Column and a packed Carboxen-1000 Column with argon as the carrier gas. The volumetric gas flow rates in and out of the cell were measured with a bubble column. The FE of a gas product is calculated as follows:
Where xi is the volume fraction of the gas product i, V is the outlet gas flow rate in L s−1, P is atmosphere pressure 101.325 kPa, R is the ideal gas constant 8.314 J mol−1 K−1, T is the room temperature in K, ni is the number of electrons required to produce one molecule of product F is the Faraday Constant 96485 C mol−1, and J is the total current in A.
The liquid products from the cathode side of the SC-BPMEA were collected using a cold trap cooled to 0 °C. The collected liquid was combined with anolyte (some crossover liquid product) for quantifying by the proton nuclear magnetic resonance spectroscopy (1H NMR) on an Agilent DD2 500 spectrometer in D2O using water suppression mode and dimethyl sulfoxide (DMSO) as the internal standard. For each plot of liquid product quantification, fresh anolyte was used, and the duration of the collection was 30 min. The FE of a liquid product is calculated as follows:
Where mi is the quantity of the liquid product i in mole, t is the duration of product collection (1800 s).
The CO2 SPU calculation is detailed in SI1 of Supplementary Information.
The electrochemical reaction model was performed by COMSOL Multiphysics version 5.5. This simulation was built upon previous modelling work27,28,29,30. The local pH and different species concentrations were simulated for different catholyte thicknesses (16, 65, 125, and 250 μm). Two different catholytes (K2SO4 and KHCO3) were used in the simulation. All the chemical reactions between species were considered in this one-dimensional modelling. The simulation (Fig. 6) included a 50 μm thick gas diffusion layer (GDL), a 0.1 μm thick Cu cathode catalyst (CL), a catholyte region with various thicknesses indicated above, and a cation exchange layer (CEL) boundary.
GDL and CL refer to gas diffusion layer and catalyst layer, respectively.
Constant concentration (Dirichlet) boundary conditions were used. Specifically, a constant concentration 37.8 mM of CO2 was assumed within the GDL layer, as this region is in direct contact with the input CO2 flow and thus assumed to be at equilibrium with gas phase CO2 over this region for the purposes of the simulation. The BPM was interpreted as a boundary with a constant species concentration (1 M H3O+ at the CEL surface)18,31, because it was assumed to generate protons as the dominant ionic charge carrier at a constant rate under constant current density (200 mA cm−2).
A user-controlled mesh is employed in the COMSOL simulation. Edge type of mesh is used for GDL, CL, catholytes, respectively. Specifically, the mesh distribution is predefined with an interval of 500 nm for GDL and catholytes, and an interval of 5 nm for CL.
Five different electrode reactions were considered at the cathode catalyst layer in this simulation. Specifically, the hydrogen evolution reaction and CO2 reduction reactions to CO, CH4, C2H4, and C2H5OH occurred at the cathode catalyst layer. In SC-BPMEA, the catalyst layer is immersed in a catholyte. Thus the simulation considers no gas-phase transport in the catalyst layer. The carbonate equilibrium reactions, corresponding catholyte buffer reactions, and a water dissociation reaction were considered in the catholyte region. The electrochemical reaction rates of the specific products were determined from experimental results. They are calculated based on the same manner as previous work17.
The electrochemical reactions at cathode catalyst layer:
The heterogenous electrochemical reaction rates are determined by the following equations:
Where Ii represents the partial current density for CO, CH4, C2H4, and C2H5OH occurred at the cathode catalyst layer, respectively. ni represents the number of electrons transferred per mole reactant. F represents faraday’s constant. Itotal represents the total current density. The FEs for the specific product is determined by the experimental results shown in Fig. 3e. ε represents the catalyst porosity value. Lcatalyst represents the cathode catalyst length.
The chemical reactions at the catholyte region and the corresponding forward kf rate constants and reverse kr rate constants taken from the literature32 (see Supplementary Table 3).
The Transport of Diluted Species physics model was used. The Nernst-Planck set of equations governed the species diffusion, and they were calculated in the same manner as previous work13,14. Migration was ignored for simplicity as the experiments were performed in the concentrated electrolyte. The ion species transport is thus calculated by solving the two equations below.
Where Ji is the molar flux, and ri represents the heterogeneous electrode reactions for CO2 reduction that were modelled at the cathode catalyst layer. Ri represents the rates of the homogeneous reactions indicated above. The Millington and Quirk model is used to determine the effective diffusivity, Di. εp represents porosity coefficient. τF,i represents tortuosity coefficient.
The porosity value of 0.6 was used for the cathode catalyst and the porosity value of 1 for the catholyte region. The species diffusion coefficients are listed in Supplementary Table 433,34,35,36.
Henry’s law and sets of Sechenov equation are applied to calculate the CO2 concentration. The concentration of CO2 in electrolytes depends on temperature and pressure. It is estimated in the same manner as previous work13,14. The Sechenov coefficients are listed in Supplementary Table 537.
We evaluated the energy consumptions for electrolyzer electricity, cathodic separation, and anodic separation in the context of ethylene. We consider the state-of-the-art CO2RR systems from the literature, including alkaline flow-cell electrolyzers, neutral MEA electrolyzers, acidic flow-cells, and MEAs. This consideration is based on the performance metrics, including selectivity, productivity, and full-cell voltage—the combination reflects as energy intensity of producing multi-carbon products (i.e., ethylene). The proximity of these performance metrics will help refine the effect of anodic and cathodic separation on the energy requirement for producing ethylene. We summarize the input parameters to the model for all the systems. The energy assessment model, as well as the assumptions, are based on the previous work5. Ideally, it will be interesting to use experimental/modelling data corresponding to the exact gas composition from the CO2-to-C2+ device. However, at present, there is a gap in published literature. We, therefore, employed one of the most widely used models38 (i.e., biogas upgrading) as the best approximation for evaluating the energy cost associated with cathode gas separation. The details of calculations for the carbon regeneration (for alkaline flow cell) and cathodic separation (for all the electrolyzers), can be found in previous work26. The anodic separation (for neutral MEA electrolyzer) is modelled based on an alkaline capture solvent39. The amount of CO2 crossover to the anode is calculated for one tonne of ethylene produced. The energy required to separate the CO2/O2 mixture is calculated based on a recent report by Carbon Engineering40, in which 5.25 GJ/tonne CO2 thermal energy and 77 kWh/tonne CO2 are reported to be required to capture CO2 and release at 1 bar. This energy consumption is a typical value for the alkaline capture process39. For acidic flow-cell and MEA electrolyzers, we assume no energy cost associated with the anodic separation considering no CO2 availability at the anodic gas stream13.
All the data generated in this study are provided in the Supplementary Information and in the Source Data file. Source data are provided with this paper.
De Luna, P. et al. What would it take for renewably powered electrosynthesis to displace petrochemical processes? Science 364, eaav3506 (2019).
Dinh, C. T. et al. CO2 electroreduction to ethylene via hydroxide-mediated copper catalysis at an abrupt interface. Science 360, 783–787 (2018).
Article CAS Google Scholar
Kibria, M. G. et al. Electrochemical CO2 reduction into chemical feedstocks: From mechanistic electrocatalysis models to system design. Adv. Mater. 31, 1–24 (2019).
Article Google Scholar
Shin, H., Hansen, K. U. & Jiao, F. Techno-economic assessment of low-temperature carbon dioxide electrolysis. Nat. Sustain 4, 911–919 (2021).
Article Google Scholar
Ozden, A. et al. Cascade CO2 electroreduction enables efficient carbonate-free production of ethylene. Joule https://doi.org/10.1016/j.joule.2021.01.007 (2021).
Rabinowitz, J. A. & Kanan, M. W. The future of low-temperature carbon dioxide electrolysis depends on solving one basic problem. Nat. Commun. 11, 10–12 (2020).
Article Google Scholar
Li, Y. C. et al. CO2 electroreduction from carbonate electrolyte. ACS Energy Lett. 4, 1427–1431 (2019).
Article CAS Google Scholar
Ma, M., Kim, S., Chorkendorff, I. & Seger, B. Role of ion-selective membranes in the carbon balance for CO2 electroreduction: Via gas diffusion electrode reactor designs. Chem. Sci. 11, 8854–8861 (2020).
Article CAS Google Scholar
Vermaas, D. A. & Smith, W. A. Synergistic electrochemical CO2 reduction and water oxidation with a bipolar membrane. ACS Energy Lett. 1, 1143–1148 (2016).
Article CAS Google Scholar
Yang, K. et al. Cation-driven increases of CO2 utilization in a bipolar membrane electrode assembly for CO2 electrolysis. ACS Energy Lett. 6, 4291–4298 (2021).
Article CAS Google Scholar
Ma, M., Clark, E. L., Chorkendorff, K. T. T. S. D. & Seger, B. Insights into the carbon balance for CO2 electroreduction on Cu using gas diffusion electrode reactor designs. Energy Environ. Sci. 13, 977–985 (2020).
Article CAS Google Scholar
Salvatore, D. A. et al. Electrolysis of gaseous CO2 to CO in a flow cell with a bipolar membrane. ACS Energy Lett. 3, 149–154 (2018).
Article CAS Google Scholar
Huang, J. E. et al. CO 2 electrolysis to multi-carbon products in strong acid. Science 372, 1074–1078 (2021).
Article ADS CAS Google Scholar
O’Brien, C. P. et al. Single pass CO2 conversion exceeding 85% in the electrosynthesis of multicarbon products via local CO2 regeneration. ACS Energy Lett. 6, 2952–2959 (2021).
Article Google Scholar
Xing, Z., Hu, L., Ripatti, D. S., Hu, X. & Feng, X. Enhancing carbon dioxide gas-diffusion electrolysis by creating a hydrophobic catalyst microenvironment. Nat. Commun. 12, 1–11 (2021).
Article Google Scholar
Clark, E. L. et al. Standards and protocols for data acquisition and reporting for studies of the electrochemical reduction of carbon dioxide. ACS Catal. 8, 6560–6570 (2018).
Article CAS Google Scholar
Oener, S. Z., Foster, M. J. & Boettcher, S. W. Accelerating water dissociation in bipolar membranes and for electrocatalysis. Science 369, 1099–1103 (2020).
Article ADS CAS Google Scholar
Bui, J. C., Digdaya, I., Xiang, C., Bell, A. T. & Weber, A. Z. Understanding multi-ion transport mechanisms in bipolar membranes. ACS Appl. Mater. Interfaces 12, 52509–52526 (2020).
Article CAS Google Scholar
Oener, S. Z., Ardo, S. & Boettcher, S. W. Ionic processes in water electrolysis: The role of ion-selective membranes. ACS Energy Lett. 2, 2625–2634 (2017).
Article CAS Google Scholar
Ozden, A. et al. High-rate and efficient ethylene electrosynthesis using a catalyst/promoter/transport layer. ACS Energy Lett. 5, 2811–2818 (2020).
Article CAS Google Scholar
Gabardo, C. M. et al. Continuous carbon dioxide electroreduction to concentrated multi-carbon products using a membrane electrode assembly. Joule 3, 2777–2791 (2019).
Article CAS Google Scholar
Li, F. et al. Molecular tuning of CO2-to-ethylene conversion. Nature 577, 509–513 (2020).
Article CAS Google Scholar
Wang, Y. et al. Catalyst synthesis under CO2 electroreduction favours faceting and promotes renewable fuels electrosynthesis. Nat. Catal. 3, 98–106 (2020).
Article CAS Google Scholar
Wang, X. et al. Efficient electrically powered CO2-to-ethanol via suppression of deoxygenation. Nat. Energy 5, 478–486 (2020).
Article ADS CAS Google Scholar
Xu, F. et al. Study of electro-osmotic drag coefficients in Nafion membrane in acid, sodium and potassium forms by electrophoresis NMR. J. Memb. Sci. 536, 116–122 (2017).
Article CAS Google Scholar
Sisler, J., Shaihroz, K., Ip, A. H., Jaffer, M. W. S. S. A. & Sargent, E. H. Ethylene electrosynthesis: A comparative techno-economic analysis of alkaline vs membrane electrode assembly vs CO2−CO− C2H4 Tandems. ACS Energy Lett. 6, 997–1002 (2021).
Article ADS CAS Google Scholar
Weng, L. C., Bell, A. T. & Weber, A. Z. Modeling gas-diffusion electrodes for CO2 reduction. Phys. Chem. Chem. Phys. 20, 16973–16984 (2018).
Article CAS Google Scholar
Singh, M. R., Clark, E. L. & Bell, A. T. Effects of electrolyte, catalyst, and membrane composition and operating conditions on the performance of solar-driven electrochemical reduction of carbon dioxide. Phys. Chem. Chem. Phys. 17, 18924–18936 (2015).
Article CAS Google Scholar
Singh, M. R., Goodpaster, J. D., Weber, A. Z., Head-Gordon, M. & Bell, A. T. Mechanistic insights into electrochemical reduction of CO2 over Ag using density functional theory and transport models. Proc. Natl Acad. Sci. USA 114, E8812–E8821 (2017).
Article ADS CAS Google Scholar
Weng, L. C., Bell, A. T. & Weber, A. Z. Towards membrane-electrode assembly systems for CO2 reduction: A modeling study. Energy Environ. Sci. 12, 1950–1968 (2019).
Article CAS Google Scholar
Vermaas, D. A., Sassenburg, M. & Smith, W. A. Photo-assisted water splitting with bipolar membrane induced pH gradients for practical solar fuel devices. J. Mater. Chem. A 3, 19556–19562 (2015).
Article CAS Google Scholar
Chen, Y., Lewis, N. S. & Xiang, C. Modeling the performance of a flow-through gas diffusion electrode for electrochemical reduction of CO or CO2. J. Electrochem. Soc. 167, 114503 (2020).
Article ADS CAS Google Scholar
Petr, V. Ionic conductiVity and diffusion at infinite dilution. CRC Handb. Chem. Phys. 96, 5–98 (1996).
Google Scholar
Aqion. Table of Diffusion Coefficients. https://www.aqion.de/site/diffusion-coefficients (2020).
Applin, K. R. & Lasaga, A. C. The determination of SO42-, NaSO4-, and MgSO40 tracer diffusion coefficients and their application to diagenetic flux calculations. Geochim. Cosmochim. Acta 48, 2151–2162 (1984).
Article ADS CAS Google Scholar
Sugisaki, M. Soret coefficients and heat of transport of polyvalent electrolytes in an aqueous solution. Bull. Chem. Soc. Jpn. 48, 2751 (1975).
Weisenberger, S. & Schumpe, A. Estimation of gas solubilities in salt solutions at temperatures from 273 K to 363 K. AIChE J. 42, 298–300 (1996).
Article CAS Google Scholar
Ebbesen, S. D. & Mogensen, M. Techno-economic assessment of low-temperature carbon dioxide electrolysis. Nat. Sustain. https://doi.org/10.1002/9780470456309.ch25 (2021).
Renfrew, S. E., Starr, D. E. & Strasser, P. Electrochemical approaches toward CO2 capture and concentration. ACS Catal. 10, 13058–13074 (2020).
Article CAS Google Scholar
Keith, D. W., Holmes, G., St. Angelo, D. & Heidel, K. A process for capturing CO2 from the atmosphere. Joule 2, 1573–1594 (2018).
Article CAS Google Scholar
Ma, S. et al. One-step electrosynthesis of ethylene and ethanol from CO2 in an alkaline electrolyzer. J. Power Sources 301, 219–228 (2016).
Article ADS CAS Google Scholar
Yan, Z., Hitt, J. L., Zeng, Z., Hickner, M. A. & Mallouk, T. E. Improving the efficiency of CO2 electrolysis by using a bipolar membrane with a weak acid cation exchange layer. Nat. Chem. 13, 33–40 (2021)
Download references
The authors acknowledge Ontario Centre for the Characterization of Advanced Materials (OCCAM) for sample preparation and characterization facilities. This work received financial support from TOTAL S.E., Fund No. 508641. R.K.M. thanks NSERC, Hatch, and the Government of Ontario for their support through graduate scholarships. D.S. acknowledges the NSERC E.W.R Steacie Memorial Fellowship. S.W.B. acknowledges funding for the bipolar membrane work from the U.S. Office of Naval Research, grant number N00014-20-1-2517.
These authors contributed equally: Ke Xie, Rui Kai Miao.
Department of Electrical and Computer Engineering, University of Toronto, 10 King’s College Road, Toronto, ON, M5S 3G4, Canada
Ke Xie, Zhu Chen, Jianan Erick Huang, Geonhui Lee & Edward H. Sargent
Department of Mechanical and Industrial Engineering, University of Toronto, 5 King’s College Road, Toronto, ON, M5S 3G8, Canada
Rui Kai Miao, Adnan Ozden, Shijie Liu, Christine M. Gabardo, Jonathan P. Edwards, Colin P. O’Brien & David Sinton
Department of Chemical Engineering, Queen’s University, 19 Division Street, Kingston, Kingston, ON, K7L 3N6, Canada
Cao-Thang Dinh
Department of Chemistry and Biochemistry, University of Oregon, Eugene, OR, 97403, USA
Qiucheng Xu & Shannon W. Boettcher
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
You can also search for this author in PubMed Google Scholar
E.H.S. and D.S. supervised the project. K.X. introduced the concept, fabricated membrane with the advice from Q.X and S.W.B., performed electrochemical measurements and wrote the manuscript. R.K.M. performed CO2 utilization measurements, advised electrolyzer design, and contributed to the manuscript editing. A.O. prepared electrodes, advised electrolyzer design and contributed to the manuscript editing. S.L. performed the one-dimensional physics modelling. J.E.H, C.M.G., Q.S., C.T.D., Z.C., G.L., J.P.E. C.O. and S.W.B contributed to the discussions and manuscript editing.
Correspondence to David Sinton or Edward H. Sargent.
K.X., R.K.M., D.S., and E.H.S. have filled a provisional patent application: US 63/201,675 on the SC-BPMEA structure described here. The remaining authors declare no competing interests.
Nature Communications thanks Jose Solla-Gullón, and the other anonymous reviewers for their contribution to the peer review of this work.
Publisher’s note Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
Reprints and Permissions
Xie, K., Miao, R.K., Ozden, A. et al. Bipolar membrane electrolyzers enable high single-pass CO2 electroreduction to multicarbon products. Nat Commun 13, 3609 (2022). https://doi.org/10.1038/s41467-022-31295-3
Download citation
Received: 14 March 2022
Accepted: 10 June 2022
Published: 24 June 2022
DOI: https://doi.org/10.1038/s41467-022-31295-3
Anyone you share the following link with will be able to read this content:
Sorry, a shareable link is not currently available for this article.
Provided by the Springer Nature SharedIt content-sharing initiative
Communications Chemistry (2023)
Nano Research (2023)
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.